American Best Tools

Founded in 1966 by Bill Martin.
His foundry cast all the same tools as MoClamp
0045 45 Degree Clamp
$ 94 
This clamp is designed to reach the hard areas. Pointed teeth for a strong bite.
0050 Small Clamp
$ 72 
1 ½ inch wide to grab the tight areas. Pear ring to use with a slide hammer
0100 Body Buddy Clamp
$ 89 
One of the first clamps ever made. This is a real workhorse with 2 ¼” wide bite and heavy build.
0200 Big Flange Clamp
$ 100 
This is another original clamp with a 2-inch bite, Sharp cross-hatch teeth
0205 Small Flange Clamp
$ 74 
Smaller version with a 1 ¼ wide bite. Cross hatch teeth, spring loaded
0250 Medium Flange Clamp
$ 82 
Original clamp for heavy work on frames. Uses a 3/4 inch bolt
0300 Clamp
$ 107 
Another original clamp with cross hatch teeth. 1 ½ inch bite. Front is tapered to reach into tight areas. Spring loaded
0305 Small Tightnose Clamp
$ 75 
1 ¼ wide with very pointed nose to bite small areas. Spring loaded. Great to use with a slide hammer or frame machine
0405 W Clamp
$ 92 
Small but having a 2 ¼ wide bite this is a great clamp to use with a slide hammer. Very pointed nose allows you access to small areas. Spring loaded
0440 Double Claw Clamp
$ 98 
Big and strong open clamp. If something is in the way this will work. Clamps over larger lips or seams. Wedge design to tighten more as the pull increases.
0660 Long Reach Clamp
$ 100 
1 ¾ inch wide jaws. Built very heavy with a wedge pull. Spring loaded, and made with cross hatch teeth.
0670 Small Box Clamp
$ 120 
Mated to 0660 with 1 ¾ wide creates a flat side and a box side. Built heavy to work everyday.
0680 Big Box Clamp
$ 137 
Two large box clamps bolted together. 1 ¾ wide clamping area. Spring loaded
0800 Weld plate tool
$ 0 
lorem psum lorem psum lorem psum lorem psum lorem psum lorem psum lorem psum
0805 Weld plates
$ 0 
lorem psum lorem psum lorem psum lorem psum lorem psum lorem psum lorem psum
1000 Chain Hook
$ 48 
One of our older chain hooks to grab sheet metal and tear out a section,or chain to a floor lip or edge of frame achine to secure a full frame.
1100 Chain Link
$ 56 
All cast steel to take up slack of a chain. Use to connect two short chains.
1250 Panel Puller
$ 54 
Nice and lightweight to pull fenders, lips Use with a slide hammer or frame rack.
1300 Sill Clamp
$ 79 
Wide flat machined surface of 2 ½ inch to make stronger pulls. Sharp teeth machined into the flat area to bite.
1450 Bolted chain Pull
$ 38 
Steel cast for 3/8 chain. ½ inch bolt for bolting to strut puller or any other clamp to add extra pulling device.
1650 Double Chain Plate
$ 78 
Designed for 3/8 chain. Two chains to be pulled at the same time.
1700 Chain Fork
$ 55 
Made to lock a 3/8 chain, Used on floor systems or frame machines.
1750 Chain Lock
$ 52 
This locks a 3/8 chain plus it is tapered to use on some brands of frame racks
1800 Track Grabber
$ 61 
When tying a full-frame vehicle these are handy to grab the outside lip of a frame machine and secure the frame.
2400 Strut Puller
$ 152 
When pulling a strut tower straight this has three legs that bolt to any hole or slot. Then a frame machine can pull on the plate to straighten the tower. The 1450 bolt to any place on the plate to hold a chain.
3071 Four Floor Anchors
$ 132 
These are the ORIGINAL 3 ½ inch floor Pots designed by Bill Martin and sold through Snap On tools. Nothing compares to the quality of these
3071 Six Floor Anchors
$ 194 
These are the ORIGINAL 3 ½ inch floor Pots designed by Bill Martin and sold through Snap On tools. Nothing compares to the quality of these
3071 Two Floor Anchors
$ 78 
These are the ORIGINAL 3 ½ inch floor Pots designed by Bill Martin and sold through Snap On tools. Nothing compares to the quality of these
3100 Sheet Metal Hooks
$ 98 
We sell a set of two. One has a flat machined area to hold to sheet metal. The other is ¾ round. Swivel eye
4010 Pinchweld Clamps
$ 196 
Pinchweld Clamps With Bar Two 4025 frame clamps mounted to a bar. Includes a shackle
4025 Pinchweld Clamp
$ 110 
The Pinchweld Clamp is good for many uses. Strong 4-inch wide bite with cross-hatch teeth. Includes a pear ring.
4058 Multi Angle Clamp
$ 138 
Includes large 3/8 plate with holes, angle with holes, bolts, and springs. Make pulls from different angles at the same time.
4110 Single Claw Hook
$ 40 
They are designed for a 3/8 chain. It's made to hook another chain at any link. Or grab a lip on a frame machine.
4120 Double Claw
$ 45 
They are used to shorten two chains or hook two chains together without hooks. Can use a chain anywhere to secure a frame.
4130 Hole Plug
$ 56 
Made for 3/8 chain. All four sides have different designs to lock inside holes of framed vehicles. This is a great tool to secure a full frame to a rack.
4150 Double Looper
$ 100 
Two single claws tied together with a pear ring.
5616 Door Post Puller
$ 70 
Steel plate with slots to match any hinge bolt pattern. Loop to then pull the door post out.
5623 Door Post plate
$ 62 
Same as 5616 but a different design.
5800 G Clamp
$ 167 
Areas that will not clamp simply C - clamp the metal and then pull.
6300 Nylon Sling
$ 49 
About 30 inches long with a loop sewn on each end. Middle area triple sewn. USA made
6301 4” Sling
$ 51 
Made with 4-inch material and steel Triangles sewn on each end. Total Length about 24 inches triple sewn In the middle.
6302 4” Sling with Pear And Triangle
$ 83 
Can use as a choker or sling
6400 Deep Hook Set
$ 232 
About 14 inches tall. For hard-to-reach areas like the trunk or door pillar, Includes two feet for wide or narrow
6600 Chain Snugger
$ 85 
Made to tighten 3/8 chains on frame machines.